ToolBarn.com

The AmPro Double Flaring Tool Set contains seven double flare adaptors in standard (SAE) measurements and is designed to withstand high pressure and double flares soft steel and single flares brass, copper and aluminum.

Learn more about the AmPro T73360

The AmPro Double Flaring Tool Set contains seven double flare adaptors in metric measurements and is designed to withstand high pressure and double flares soft steel and single flares brass, copper and aluminum.

Learn more about the AmPro T73361

Flare 7 sizes of soft copper, aluminum and brass tubing, Forged steel slip on yoke and hardened flaring bar, Yoke design permits flaring where there is little space between nut and tube end, Positive clamping of bars prevents tube slippage,… Learn more about the Malco Tools FT195

For soft copper, aluminum and brass tubing, Faceted, hard chrome finished cone rolls out perfect 45° flares - then automatically burnishes flare face, Handy slip-on yoke permits use in tight quarters, Movable dies allow tubing to be slipped in easily,… Learn more about the Malco Tools FT500

Pocket size reamer deburrs nominal 1/4" or larger tubing and fittings, Freely rotating, hardened steel blade holds its edge in both copper and ABS/PVC plastic, Under 6" overall length, Learn more about the Malco Tools R308

Knurled stock for easy removal of punch., Learn more about the Malco Tools ST94

Hexagon stock allows easy removal of punch, Combination swaging punch is three sizes in one tool, Knurled stock for easy removal of punch, Expand copper pipe to create female fitting, Learn more about the Malco Tools ST96

7 sizes from 3/16" to 5/8", For use in producing 45 degree flares for 3/16" to 5/8" tubing, Model 345 is a precision designed tool for producing 45 degree flares in soft copper, brass, aluminum, and mild steel, A… Learn more about the Ridgid 23332

Added to a Ridgid 345 series flaring tool, this 3/16" double lap flaring adaptor will allow you to produce double lap flares on the ends of your tubing. Double lap flares add additional strength to tube ends that are likely to endure more stress than standard ends.

Learn more about the Ridgid 31597

Added to a Ridgid 345 series flaring tool, this 1/4" double lap flaring adaptor will allow you to produce double lap flares on the ends of your tubing. Double lap flares add additional strength to tube ends that are likely to endure more stress than standard ends.

Learn more about the Ridgid 31602

Added to a Ridgid 345 series flaring tool, this 5/16" double lap flaring adaptor will allow you to produce double lap flares on the ends of your tubing. Double lap flares add additional strength to tube ends that are likely to endure more stress than standard ends.

Learn more about the Ridgid 31607

The Ridgid 33927, or 345DL/150, is a 45° SAE flaring tool for 3/16 to 5/8" tubing, adaptors for 3/16" to 1/2" double lap flares and a 1/8" - 1-1/8" tubing cutter with an extra wheel and a built-in reaming tool.

Learn more about the Ridgid 33927

The Ridgid 41162 (or 377) flaring tool delivers a 37 degree SAE flare to copper or aluminum pipes or tubing that are 3/16, 1/4, 5/16, 3/8, 1/2, 5/8 or 3/4 of an inch in diameter.

Learn more about the Ridgid 41162

Provides smooth, uniform flares with minimum effort and galling, Requires less motion and effort than a standard handle, Hardened steel flaring cone, Eccentrically mounted in needle bearings, produces rolling action for even metal flow giving uniform flare walls without… Learn more about the Ridgid 41295

This E-47 hammer-tyoe flaring tool from Ridgid creates 45º flares in 3/4" water tubing. (41330)

Learn more about the Ridgid 41330

This E-52 hammer-tyoe flaring tool from Ridgid creates 45º flares in 1" water tubing. (41335)

Learn more about the Ridgid 41335